Thiết bị mạng
Module quang Aruba J4859D 1990-4416 1000Base-LX SFP LC Duplex XCVR 10km 1310nm SMF Transceiver
Thông số kỹ thuật Module quang Aruba J4859D:
Mode | Single-mode Fiber (SMF) |
Model | J4859D |
Data-rate | 1000BASE-LX |
Form-factor | SFP |
Connector | LC Duplex |
Wavelength | 1310nm |
Max Cable Distance | 10km |
Max Data Rate | 1000Mbps |
Cable Type | SMF |
R8N86A Aruba 6000 48G 4 SFP Switch
Tổng quan Switch Aruba R8N86A
Datasheet | R8N86A |
SPECIFICATIONS | |
Description | – 48x ports 10/100/1000BASE-T Ports
– 4x 1G SFP ports – 1x USB-C Console Port – 1x USB Type-A Host port |
Power supplies | Fixed power supply |
Fans | Fixed fans |
Physical characteristics | |
Dimensions | (H) 4.39 cm
(W) 44.2 cm (D) 24.74 cm (1.73” x 17.4” x 9.74”) |
Configuration Weight | 3.42 kg (7.54 lbs) |
Additional Specifications | |
CPU | Dual Core ARM Cortex A9 @ 1016 Mhz |
Memory and Flash | 4 GB DDR3
16 GB eMMC |
Packet Buffer | 12.38MB (4.5MB Ingress/7.875MB Egress) |
Performance | |
System Switching Capacity | Up to 104 Gbps |
System Throughput Capacity | Up to 77.3 Mpps |
Average Latency (LIFO-64- bytes packets) | 1 Gbps: 1.9 μSec , 10 Gbps: 1.8 μSec |
Switched Virtual Interfaces (dual stack) | 16 |
IPv4 Host Table (ARP) | 1,024 |
IPv6 Host Table (ND) | 512 |
IPv4 Unicast Routes | 512 |
IPv6 Unicast Routes | 512 |
MAC Table Capacity | 8,192 |
IGMP Groups | 512 |
MLD Groups | 512 |
IPv4/IPv6/MAC ACL Entries (ingress) | 256 / 128 / 256 |
R8N87A Aruba 6000 24G Class4 PoE 4SFP 370W Switch
Tổng quan Switch Aruba R8N87A
Datasheet R8N87A | |
SPECIFICATIONS | |
Description | – 24x ports 10/100/1000BASE-T Ports Supports PoE Standards IEEE 802.3af, 802.3at
– 4x 1G SFP ports – 1x USB-C Console Port – 1x USB Type-A Host port |
Power supplies | Fixed power supply |
Fans | Fixed fans |
Physical characteristics | |
Dimensions | (H) 4.39 cm
(W) 44.2 cm (D) 26.82 cm (1.73” x 17.4” x 10.56”) |
Configuration Weight | 4.19kg (9.24 lbs) |
Additional Specifications | |
CPU | Dual Core ARM Cortex A9 @ 1016 Mhz |
Memory and Flash | 4 GB DDR3
16 GB eMMC |
Packet Buffer | 12.38MB (4.5MB Ingress/7.875MB Egress) |
Performance | |
Switching Capacity | 104 Gbps |
Throughput Capacity | 77.3 Mpps |
Average Latency (LIFO-64-bytes packets) | 1 Gbps: 1.5 μSec , 10 Gbps: 1.8 μSec |
Switched Virtual Interfaces (dual stack) | 16 |
IPv4 Host Table (ARP) | 1,024 |
MLD Groups | 512 |
IPv4/IPv6/MAC ACL Entries (ingress) | 1,024 |
Switch Aruba Instant On 1930 8G Class 4 PoE 2SFP 124W (JL681A)
- Switch Aruba 8G Class 4 PoE 2SFP 124W Là thiết bị chuyển mạch 8 port Gigabit cấp nguồn PoE với 2 cổng quang (SFP ) được quản trị ở Layer 2. Là dòng sản phẩm mới của hãng Aruba, với giá cả phải chăng và dể dàng triển khai rất phù hợp với các doanh nghiệp vừa và nhỏ.
- Dòng switch quản trị lớp 2+ được thiết kế với 8 port, 24 và 48 port bao gồm không cấp nguồn PoE và có cấp nguồn PoE+
- PoE cấp nguồn cho các thiết bị AP, điện thoại IP Phone, Camera, khóa cửa
- 2 cổng quang 1G SFP trên switch 8 port và 4 cổng quang 1G/10G SFP+ trên switch 24/48 port giúp loại bỏ tắc nghẽn lưu lượng trên hệ thống mạng của bạn
- Kiểm soát bảo mật cho phép bạn xác định quyền truy cập cho từng khu vực mạng, giữ cho dữ liệu của bạn được an toàn
- Sử dụng ứng dụng trên điện thoại và web-GUI giúp cho việc cài đặt, cấu hình quản trị cũng như xử lý sự cố trở nên đơn giản và dễ dàng
Switch Aruba R8N85A 48xGE JR45, 4xSFP, 48 Ports PoE 370W
Thông số kỹ thuật Switch Aruba R8N85A
Datasheet | R8N85A |
SPECIFICATIONS | |
Description | – 48x ports 10/100/1000BASE-T Ports Supports PoE Standards IEEE 802.3af, 802.3at
– 4x 1G SFP ports – 1x USB-C Console Port – 1x USB Type-A Host port |
Power supplies | Fixed power supply
Up to 370W of Class 4 PoE Power |
Fans | Fixed fans |
Physical characteristics | |
Dimensions | (H) 4.39 cm
(W) 44.2 cm (D) 24.74 cm (1.73” x 17.4” x 9.74”) |
Configuration Weight | 3.42 kg (7.54 lbs) |
Additional Specifications | |
CPU | Dual Core ARM Cortex A9 @ 1016 Mhz |
Memory and Flash | 4 GB DDR3
16 GB eMMC |
Packet Buffer | 12.38MB (4.5MB Ingress/7.875MB Egress) |
Performance | |
System Switching Capacity | 104 Gbps |
System Throughput Capacity | 77.3 Mpps |
Average Latency (LIFO-64- bytes packets) | 1 Gbps: 1.9 μSec , 10 Gbps: 1.8 μSec |
Switched Virtual Interfaces (dual stack) | 16 |
IPv4 Host Table (ARP) | 1,024 |
IPv6 Host Table (ND) | 512 |
IPv4 Unicast Routes | 512 |
IPv6 Unicast Routes | 512 |
MAC Table Capacity | 8,192 |
IGMP Groups | 512 |
MLD Groups | 512 |
IPv4/IPv6/MAC ACL Entries (ingress) | 256 / 128 / 256 |
Thiết Bị Cân Bằng Tải DrayTek V2927 (LOAD BALANCING/2WAN1000/5LAN1000/2USB)
‘High Througput Enterprise Dual-Gigabit Wan Load Balancing Router – Chuyên nghiệp cho Doanh Nghiệp/ Nhà Hàng / Khách Sạn chịu tải 150 user- Hỗ trợ WiFi Marketing
– 2 cổng Wan Gigabit RJ45 (Wan 2 chuyển đổi từ port LAN 6)
– 5 cổng Lan Gigabit, hỗ trợ VLAN tag 802.1q chia 16 VLAN (8 Subnet)
– 2 cổng USB kết nối USB 3G/4G, Printer,…
– NAT Session: 60.000 / NAT Throughput: 1.8 Gbps (Dual Wan), chịu tải 150 user
– Cân bằng tải (cộng gộp băng thông) hoặc dự phòng các đường truyền internet (Loadbalance/ Failover
– Hỗ trợ triển khai dịch vụ cao cấp: Static IP, PPOE, PPTP/L2TP, DHCP…
– Hỗ trợ các dịch vụ: Leasedline, L2VPN, L3VPN, MetroNET… trên sub interface (NAT hoặc Routing)
– Hỗ trợ đường truyền đa dịch vụ (IPTV, Internet, VoIP,…)
– VPN Server 50 kênh (PPTP, L2TP, IPSec(IKEv1, IKEv2), SSL), Open VPN + SSL VPN: 25
– IPsec VPN Performnace: 290Mbps / SSL VPN Performance: 120Mbps
– Kiểm soát và quản lý băng thông giúp tối ưu hóa đường truyền internet
– Firewall mạnh mẽ, linh hoạt, quản trị phân quyền truy cập Internet (IP/MAC Address, Port Service, URL/Web content filter, schedule…), Firewall SPI dựa trên đối tượng, quản lý nội dung (CSM).
– Web portal: Hiện trang quảng cáo khi khách hàng kết nối internet
– Tích hợp Wi-Fi Marketing từ các nhà phát triển hàng đầu như Meganet, VNWIFI, Nextify…
– DrayDDNS tên miền động miễn phí của DrayTek
– Quản lý tập trung VPN cho 8 site Router Vigor khác qua Internet (CVM)
– Quản lý tập trung cho 20 Access Point (APM), 10 Switch (SWM)
– Quản lý tập trung Vigor2927 bằng phần mềm DrayTek VigorACS 2 hoặc cloud DrayTek Free
Thiết bị chuyển đổi quang D-Link 1-PORT LX SINGLE-MODE FIBER SFP 10KM 3.3V
SFP Transceiver – Single-Mode Fiber, dùng với cáp quang Single-Mode 9/125µm, chiều dài cáp tối đa là 10Km. Bước sóng 1310nm. Chuẩn 802.3z 1000BASE-LX (1Gbps), kết nối quang theo chuẩn LC. Module cho Switch DES-1210-28, DES-1210-52, DES-3526, DES-3828, DGS-1224T
Thiết bị chuyển mạch D-link 24*10/100/1000MBPS POE + 4 1G SFP SMART MANAGED SWITCH
- DGS-1210-28MP : 24 cổng 10/100/1000Mbps Base-T PoE + 4 cổng SFP.
- Switching Capacity: 56 Gbps.
- Tốc độ chuyển tiếp gói dữ liệu tối đa 64-byte: 14.88 Mpps.
- Bộ nhớ gói dữ liệu đệm: 1.5 MB.
- Địa chỉ MAC: 16,000 entries per device.
- Nguồn điện ngõ vào: 100 – 240VAC, 50 – 60 Hz.
- Chức năng cấp nguồn qua mạng PoE 802.3af.
- Công suất tiêu thụ tối đa: 454.4 W (PoE on); 33.1 W (PoE off).
- Kích thước: 440 x 250 x 44 mm.
- Trọng lượng: 3.86 kg.
- Support IEEE 802.3af and 802.3at POE with Power Budget up to 370 W
- Equipped with IEEE 802.3az Energy Efficient Ethernet (EEE) Complaint
- Support IEEE 802.1Q VLAN traffic segregation.
- Access Control List (ACL) feature to enhances network security.
- Auto Surveillance VLAN for easy integration with IP-based surveillance systems.
- Loopback detection (LBD) and broadcast storm control to avoid network downtime.
- Quality of Service (QOS) and bandwidth control to ensure smooth operation.
- Support Web-based GUI, Smart Console, Network Assistance Utility.
- Cable diagnostics function to help troubleshooting wiring problem.
Thiết bị chuyển mạch Switch Dlink DGS-1210-28 28-PORT GIGABIT SMART MANAGED SWITCH
– 24 Cổng RJ45 10/100/1000Mbps dùng với cáp mạng cat.5 + 4 slot 1000BASE-T/SFP.
– Tự động dò tìm tốc độ phù hợp, MDI/MDIX ( tự động chuyển đổi cáp chéo thẳng).
– Tích hợp tính năng chuyển mạch Store & Forward, tự động nhận và chuẩn đoán cáp.
– Ram buffer 1024 Kbytes, 802.1d STP, 802.1w RSTP, Port Mirror.
– VLAN (max 256 group), Auto Voice VLAN.
– Broadcast Storm Control, ARP snoofing, Port Security, Access Control List
– Hỗ trợ 802.3x Flow control, 802.1p QoS, Bandwidth Control, True Plug & Play, Jumbo Frame.
– Tốc độ chuyển mạch lên tới 48Gbps (Non-Blocking).
– Cấu hình bằng giao diện WEB GUI, Smart Console, Telnet.
– Công nghệ tiết kiệm điện Green Ethernet, RoHS Compliant, Rack 19′.
Thiết bị kết nối Bluetooth 4.0 qua cổng USB TPlink UB400
Thiết bị kết nối Bluetooth 4.0 qua cổng USB TPlink UB400
Thiết bị mạng wifi RUIJIE RG-EW1200G Pro (Router wifi cho gia đình)
– Router Wifi gia đình
– Tốc độ lên đến 1267Mbps
– Hỗ trợ 2 băng tần 2.4GHz và 5GHz chuẩn 802.11a/b/g/n/ac Wave1/Wave2, MU-MIMO
– Độ lợi Antenna 6 x 6dBi
– Số lượng người dùng truy cập đồng thời đề xuất là 30+
– 1 cổng 10/100/1000M WAN (Auto MDI/MDIX), 3 cổng 10/100/1000M LAN (Auto MDI/MDIX)
Thiết bị thu phát vô tuyến D-Link NUCLIAS CONNECT AC1200 WAVE 2 ACCESS POINT
NUCLIAS CONNECT Wireless AC1200 Wave 2 (2 x 2) Dual Band INDOOR Long Range (200M) Access Point
1 x Gigabit LAN (Support 802.3af PoE), 2.4GHz: 300Mbps & 5GHz: 867Mbps; with 2 x 3.8dBi at 2.4GHz and 2 x 3.8dBi at 5GHz, High Power Design, Support Fast Roaming (802.11 k/v/r); WPA3
PoE injector NOT INCLUDED, Power Adapter NOT INCLUDED
Thiết bị thu phát vô tuyến D-Link NUCLIAS CONNECT AX1800 WiFi 6 DUAL BAND POE ACCESS POINT
Model | DAP-X2810 |
General | |
Device Interfaces | 1 x RJ45 console port, 1 x 10/100/1000 Ethernet (PoE) LAN, factory reset, power input |
Antennas | 2 x dual-band internal antennas |
Antenna Gain | 3.2 dBi (2.4 GHz), 4.3 dBi (5 GHz) |
Maximum Output Power | 23 dBm (2.4 GHz), 26 dBm (5 GHz) |
Data Signal Rate | Up to 1800 Mbps |
LEDs | Power/Status |
Functionality | |
Standards | IEEE 802.11a/b/g/n/ac/ax, IEEE 802.3u/ab, IEEE 802.3az Energy-Efficient Ethernet (EEE), IEEE 802.3at PoE |
Operating Frequency | 2.4 – 2.483 GHz, 5.15 – 5.35 GHz, 5.47 – 5.85 GHz |
Security Protocol | WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access control, internal RADIUS server |
Software | |
Network Management | Telnet, SSH, Web (HTTP), Secure Socket Layer (SSL), Traffic control, D-Link Nuclias Connect |
Physical | |
Weight | 763.8 g |
Dimensions | 212.4 x 212.4 x 46.7 mm |
Power Supply | 12 V / 2.5 A (optional power adapter), IEEE 802.3at PoE |
Maximum Power Consumption |
19.44 W |
Operating Temperature | 0˚C to 40˚C |
Storage Temperature | -20˚C to 65 ˚C |
Operating Humidity | 10% to 90% |
Storage Humidity | 5% to 95% |
Thiết bị tường lửa D-LINK UNIFIED SERVICE ROUTER
- Tự động chuyển đổi dự phòng sang một liên kết khác từ ISP khả dụng khi đường chính bị mất.
- Hỗ trợ 1 x GE WAN, 3 x GE LAN, 1 GE Configable LAN/WAN và 1 x cổng USB 3.0.
- Thông lượng tường lửa/VPN 900/200 Mbps, 50.000 Phiên đồng thời và Đường hầm VPN 50/20 IPsec/SSL.
- Định tuyến nâng cao, VLAN và IPsec/PPTP/L2TP/OpenVPN VPN Server/Client
- Tiện ích văn phòng giá trị gia tăng để giảm OpEx/CAPEX
- Cân bằng tải lưu lượng và Tránh các vấn đề bảo trì phức tạp
Wifi Aruba AP 303 Indoor Access Point
Thông số kỹ thuật
Datasheet Aruba AP 303 | |
WI-FI Radio Specifications |
• AP type: Indoor, dual radio, 5GHz 802.11ac 2×2 MIMO and 2.4GHz 802.11n 2×2 MIMO
• 5GHz: -Two spatial stream Single User (SU) MIMO for up to 867 Mbps wireless data rate to individual 2SS VHT80
client devices -Two spatial stream Multi User (MU) MIMO for up to 867 Mbps wireless data rate to two 1SS MU-MIMO
capable client devices simultaneously • 2.4GHz: Two spatial stream Single User (SU) MIMO for up to 300 Mbps wireless data rate to individual 2SS HT40 client devices • Support for up to 255 associated client devices per radio, and up to 16 BSSIDs per radio • Supported frequency bands (country-specific restrictions apply): – 2.400 to 2.4835GHz – 5.150 to 5.250GHz
– 5.250 to 5.350GHz
– 5.470 to 5.725GHz
– 5.725 to 5.850GHz
• Available channels: Dependent on configured regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of available RF spectrum • Supported radio technologies: – 802.11b: Direct-sequence spread-spectrum (DSSS) – 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
• Supported modulation types:
– 802.11b: BPSK, QPSK, CCK – 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Configurable in increments of 0.5 dBm
• Maximum (conducted) transmit power (limited by local regulatory requirements): – 2.4GHz band: +21dBm (18dBm per chain) – 5GHz band: +21dBm (18dBm per chain)
– NOTE: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
• Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
• Maximum ratio combining (MRC) for improved receiver performance • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance • Short guard interval for 20MHz, 40MHz and 80MHz channels • Space-time block coding (STBC) for increased range and improved reception • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput • Transmit beam-forming (TxBF) for increased signal reliability and range • Supported data rates (Mbps): – 802.11b: 1, 2, 5.5, 11 – 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
– 802.11n: 6.5 to 300 (MCS0 to MCS15)
– 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support: VHT 20/40/80 • 802.11n/ac packet aggregation: A-MPDU, A-MSDU |
WI-FI Antennas | • Two vertically polarized dual-band downtilt omnidirectional antennas for 2×2 MIMO with peak antenna gain of: –3.3dBi in 2.4GHz and 5.8dBi in 5GHz for AP-303 –3.4dBi in 2.4GHz and 7.8dBi in 5GHz for AP-303P • The antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees. • Combining the patterns of both antennas per radio, the peak gain of the average (effective) pattern is: –2.1dBi in 2.4GHz and 5.7dBi in 5GHz for AP-303 –2.1dBi in 2.4GHz and 5.9dBi in 5GHz for AP-303P |
Other Interfaces | • E0: One 10/100/1000BASE-T Ethernet network interface (RJ-45) –Auto-sensing link speed and MDI/MDX –802.3az Energy Efficient Ethernet (EEE) –PoE-PD: 48Vdc (nominal) 802.3af/at/bt PoE • DC power interface • E1 (AP-303P models only): One 10/100/1000BASE-T Ethernet network interface (RJ-45) –Auto-sensing link speed and MDI/MDX –802.3az Energy Efficient Ethernet (EEE) –PoE-PSE (output): 48Vdc (nominal) 802.3af/at PoE • Bluetooth Low Energy (BLE) radio • Zigbee 802.15.4 radio (AP-303P models only) • Visual indicators (tri-color LEDs): for System and Radio status • Reset button: factory reset (during device power-up), LED mode control (normal/off) • Serial console interface (proprietary, μUSB physical jack) • Kensington security slot |
Power Sources and Consumption | • The AP supports direct DC power and Power over Ethernet (PoE) • When both power sources are available, DC power takes priority over PoE • Power sources are sold separately AP-303 models: • Direct DC source: 12Vdc nominal, +/- 5% • DC power interface accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length • Power over Ethernet (PoE): 48Vdc (nominal) 802.3af compliant source • Maximum (worst-case) power consumption: 10.1W (PoE) or 8.8W (DC) • Maximum (worst-case) power consumption in idle mode: 4.2W (PoE) or 4.0W (DC) AP-303P models: • Direct DC source: 48Vdc nominal, +/- 5% • DC power interface accepts 1.35/3.5-mm center-positive circular plug with 9.5-mm length • Power over Ethernet (PoE-PD) on E0: 48Vdc (nominal) 802.3af/at/bt compliant source • PoE-PSE function on E1 disabled when powered by 802.3af PoE, limited to class 3 when powered by 802.3at PoE, unrestricted when powered by 802.3bt PoE or DC • Maximum (worst-case) power consumption: 11.3 (PoE) or 11.5 (DC) • Maximum (worst-case) power consumption in idle mode: 6.8 (PoE) or 7.0 (DC) • Power consumption numbers exclude power to support PoE-PSE function on E1 |
Mounting | • The AP ships with a (black) mount clips to attach to a 9/16- inch or 15/16-inch flat T-bar drop-tile ceiling • Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details |
Mechanical |
• Dimensions and weight (unit, excluding mount accessories):
–150mm (W) x 150mm (D) x 35mm (H) or 5.9” (W) x 5.9” (D) x 1.4” (H) –AP-303 models: 260g or 9.2oz –AP-303P models: 280g or 9.9oz • Dimensions and weight (shipping): –190mm (W) x 180mm (D) x 60mm (H) or 7.4” (W) x 7.0” (D) x 2.4” (H) –AP-303 models: 410g or 14.5oz –AP-303P models: 430g or 15.2oz |
Environmental |
• Operating:
–Temperature: 0° C to +40° C (+32° F to +104° F) –Humidity: 5% to 93% non-condensing • Storage and transportation: –Temperature: -40° C to +70° C (-40° F to +158° F) |
Reliability (at +25C operating temperature) | • AP-303 models MTBF: 795khrs (91yrs) • AP-303P models MTBF: 518khrs (59yrs) |
Regulatory | • FCC/Industry of Canada • CE Marked • R&TTE Directive 1995/5/EC • Low Voltage Directive 72/23/EEC • EN 300 328 • EN 301 489 • EN 301 893 • UL/IEC/EN 60950 • EN 60601-1-1 and EN 60601-1-2 |
Wifi Aruba AP 505 Dual Radio 802.11ax Indoor
Thông số kỹ thuật Aruba AP-505
aruba ap 505 datasheet | |
TECHNICAL SPECIFICATIONS | |
AP type | Indoor, dual radio, 5GHz and 2.4GHz 802.11ax 2×2 MIMO |
Radio 5Ghz | Two spatial stream Single User (SU) MIMO for up to 1.2Gbps wireless data rate with individual 2SS HE80 802.11ax client devices, or with two 1SS HE80 802.11ax MU-MIMO capable client devices simultaneously |
Radio 2.4Ghz | Two spatial stream Single User (SU) MIMO for up to 574Mbps (287 Mbps) wireless data rate with individual 2SS HE40 (HE20) 802.11ax client devices or with two 1SS HE40 (HE20) 802.11ax MU-MIMO capable client devices simultaneously |
Maximum number of associated client devices | Up to 256 associated client devices per radio |
Maximum number of BSSIDs | 16 BSSIDs per radio |
Supported frequency bands (country-specific restrictions apply) | – 2.400 to 2.4835 GHz – 5.150 to 5.250 GHz – 5.250 to 5.350 GHz – 5.470 to 5.725 GHz – 5.725 to 5.850 GHz |
Available channels | Dependent on configured regulatory domain |
Supported radio technologies | – 802.11b: Direct-sequence spread-spectrum (DSSS) – 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) – 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units |
Supported modulation types | – 802.11b: BPSK, QPSK, CCK – 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension) – 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension) – 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM |
802.11n high-throughput (HT) support | HT20/40 |
802.11ac very high throughput (VHT) support: | VHT20/40/80 |
802.11ax high efficiency (HE) support: |
HE20/40/80 |
Supported data rates (Mbps): | – 802.11b: 1, 2, 5.5, 11 – 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 – 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256-QAM – 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80), 1,083 with 1024-QAM – 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40) – 802.11ax (5GHz): 3.6 to 1,201 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE80) |
802.11n/ac packet aggregation: | A-MPDU, A-MSDU |
Transmit power | Configurable in increments of 0.5 dBm |
Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): | – 2.4 GHz band: +21 dBm (18dBm per chain) – 5 GHz band: +21 dBm (18 dBm per chain) |
WI-FI ANTENNAS | |
Antenna | Two integrated dual-band downtilt omni-directional antennas for 2×2 MIMO with peak antenna gain of 4.9dBi in 2.4GHz and 5.7dBi in 5GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees. • Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 4.3dBi in 2.4GHz and 5.6dBi in 5GHz. |
OTHER INTERFACES | |
Interfaces | – Auto-sensing link speed (10/100/1000BASE-T) and MDI/MDX – POE-PD: 48Vdc (nominal) 802.3af/at POE (class 3 or 4) – 802.3az Energy Efficient Ethernet (EEE) |
DC power interface | 12Vdc (nominal, +/- 5%), accepts 2.1mm/5.5mm center-positive circular plug with 9.5mm length |
USB 2.0 host interface (Type A connector) |
Capable of sourcing up to 1A / 5W to an attached device |
Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio |
– BLE: up to 7dBm transmit power (class 1) and -93dBm receive sensitivity (1Mbps) – Zigbee: up to 6dBm transmit power and -96dBm receive sensitivity Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.3dBi |
Visual indictors (two multi-color LEDs): |
For System and Radio status |
Reset button: | Factory reset, LED mode control (normal/off) |
Serial console interface | Proprietary, micro-B USB physical jack |
Security slot | Kensington security slot |
FLEXIBLE OPERATION AND MANAGEMENT | |
Controller-less (Instant) mode | In controllerless mode, one AP serves as a virtual controller for the entire network |
Mobility Controller mode | For optimized network performance, roaming and security, APs tunnel all traffic to a mobility controller for centrally managed traffic forwarding and segmentation, data encryption, and policy enforcement. |
Management options | Aruba Central (cloud-managed) or Aruba AirWave |
POWER SOURCES AND POWER CONSUMPTION | |
Power Sources: The AP supports direct DC power and Power over Ethernet |
– The AP supports direct DC power and Power over Ethernet – When both DC and POE power sources are available, DC power takes priority over POE – Power sources are sold separately; see the 500 Series Ordering Guide for details – When powered by DC or 802.3at (class 4) POE, the AP will operate without restrictions. – When powered by 802.3af (class 3) POE and with the IPM feature disabled, the AP will disable the USB port. In the same configuration but with IPM enabled, the AP will start up in unrestricted mode, but may dynamically apply restrictions depending on the POE budget and actual power. The feature restrictions and order can be programmed. |
Maximum (worst-case) power consumption (without / with a USB device attached): |
– DC powered: 8.9W / 14.2W. – POE powered (802.3at): 11.0W / 16.5W. – POE powered (802.3af): 11.0W / 13.5W. – This assumes that up to 5W is supplied to the attached USB device. |
Maximum (worst-case) power consumption in idle mode: |
4.3W (DC) or 6.2W (POE). |
Maximum (worst-case) power consumption in deep-sleep mode: |
1.7W (DC) or 3.7W (POE). |
MECHANICAL SPECIFICATIONS | |
Dimensions/weight | – 160mm (W) x 161mm (D) x 37mm (H) – 500g |
Dimensions/weight (shipping): | – 193mm (W) x 183mm (D) x 63mm (H) – 645g |
Mounting details | A mounting bracket has been pre-installed on the back of the AP. This bracket is used to secure the AP to any of the mount kits (sold separately); see the 500 Series Ordering Guide for details. |
ENVIRONMENTAL SPECIFICATIONS | |
Operating conditions | – Temperature: 0C to +50C / +32F to +122F – Humidity: 5% to 93% non-condensing – AP is plenum rated for use in air-handling spaces – ETS 300 019 class 3.2 environments |
Storage and transportation conditions | – Temperature: -40C to +70C / -40F to +158F – Humidity: 5% to 93% non-condensing – ETS 300 019 classes 1.2 and 2.3 environments |
RELIABILITY | |
Mean Time Between Failure (MTBF): | 1.3Mhrs (148yrs) at +25C operating temperature. |
MINIMUM OPERATING SYSTEM SOFTWARE VERSIONS | |
ArubaOS | 8.6.0.0 |
Minimum Software Release | 8.6.0.0 |